Augvape Intake Sub-Ohm Tank

Hello,

 

Today I Augvape intake tank for inspection, a collaboration between MikeVapes and Augvape. MikeVapes is my favorite so critical on YouTube so my expectations are high on this one.

Many may know RTA admission, earlier taking the series. The particularity of this tank is Clapton mesh metal tape used in the coil, Augvape claim GDR like aroma. We’ll see!

 

In the box:

 

– tank intake Narada Pro Pod System VW Starter Kit

– 1 * Glass Bubble

– 1 * 0.15 ohm regular coil Mesh

– 2 * Mesh Coil Clapton

– 2 * O-rings

– 1 * User Manual

– 1 * Warranty Card

ILike that you get three coils in the kit, do not remember everything I owned tanker which has three coils in the kit. Coils, but not packed or sealed and have a visible fingerprints on them, Augvape hope that the kit will improve the future.

 

Review:

 

This beautiful container with zero brand outside of the tank, right at the bottom. I like simple search tank and that’s what it is. Carved into the “A” over the entire tank provides the right grip for each part. Overall this machine is well done and if the quality of feeling, this tank was the strongest of all the tanks SubOhm I submitted so far, and I have great hands.

Even if the tank is much better with the right lenses; glass bubbles have only a higher capacity (3.5 vs 5 ml) are important for the tank. 5ml is a kind of standard
It is easy to disassemble the entire tank to replace rolls and cleaning purposes. As the rings also come from the airflow. One thing I was struggling a bit with the tap of a coil with empty hands, too bad they do not understand the coil removal tool to make it a little easier. The coils installed easily.

Top fills easily with 90 degree locking key mechanism, as I like the SubOhm tank. Top hat offers a good grip for easy opening. It is recessed seat for the rubber stoppers are inserted into the filling hole, which ensures a good seal.

The air flow allows a lot of air, and for a beautiful limited edition. I must say that the noise of the air flow is very smooth and quiet enough for this type of tank. ring airflow moves with ease and because the peak engraved on the “A” is very easy to get good adhesion.

There is only one point drop in the kit, but it is a right dot net. In the minimum cap position because it is too short.

Let us now talk performance. I started with a wire mesh Clapton, just because it is marketed as an innovative taste and upscale. Admittedly, the taste is amazing on this coil, and what I like even more is the fact that it is probably a little warmer than usual coil Mesh, perhaps because of the design Clapton. The sense level GDR? I would say yes, at least very close. The difference with the GDR, however, is that you do not need to buy a Rolls-drop and if the performance you just fall leaves replace cotton. But for those looking for a taste of SubOhm tank with falling rolls is a good choice.

Another coil Mesh is what you expect of a mesh coil, provides a good flavor and a dense cloud. If I had to choose between the two coils, it will mesh metal Clapton, the only truly revolutionary in my opinion. In the Netherlands, we would say “A knock on the Bullseye” and I think the technology is appropriate mesh Clapton by many companies soon, it was good.
Two coils have no problems with chain vaping all, very saturated axis unabated. I’ll have some condensation buildup by high velocity air, overtime, slightly below the ring moisty flow of air,

Conclusion:

Looking for a drop tank SubOhm coil with a fantastic flavor? Then this may be your best option right now. Mesh is really great Clapton. I highly recommend this SubOhm tank, but keep in mind, it is my opinion

If there is a downside to mention that it would be difficult to take a roll with his bare hands, and the fact that the coils do not come sealed and a little dirty.
One good thing about this tank is the price, you can get them from various sites for under $ 20 and you get three coils inside the box!

Thank you for reading, take care!
Sjoerd

Leave a Reply

Your email address will not be published. Required fields are marked *